
Brinyte T28 Artemis (2019) review
The Brinyte T28 Artemis (T28) released in 2019. It uses 1 x Cree XP-L HI LED, 1 x Cree XP-E2 LED (red), 1 x Cree XP-E2 LED (green), no reflector and 1 x 21700 Li-Ion battery. The powerful emitter in this flashlight provides up to 650 lm output, 69600 cd intensity, and a beam distance of 528 m.
The memory function is a nice feature, the light will remember the last used mode.
Table of contents:
Brinyte T28 Artemis (T28) specifications
- Brand
- Brinyte
- Name
- T28 Artemis
- Type
- T28
- Rating
- Launch
- 2019
- Form
- flashlight
Body
The aluminium body of flashlight treated with a Type III hard-anodized, anti-abrasive finish.
- Weight
- 199 g
- Length
- 197 mm
- Head diameter
- 54 mm
- Material
- aluminium alloy with HAIII hard-anodized finish
- Colors
- black
System
The emitter of T28 Artemis manufactured by Cree, a US-based LED manufacturing company.
- Emitter
- 1 x Cree XP-L HI LED, 1 x Cree XP-E2 LED (red), 1 x Cree XP-E2 LED (green)
- Color temperature
- 6500 K
- Reflector
- no
- Lens
- fresnel
- Switch
- electronic side, electronic rear
Performance
The throw is the calculated distance in meters at which the flashlight produces a light intensity of 0.25 lux. The candela per lumen (cd/lm) ratio can be used to determine if a flashlight has a spot or flood type beam. Well-focused spot beams can be over 100 cd/lm, tactical flashlights are typically between 20-100 cd/lm, and work lights are less than 10 cd/lm.
- Flux
- 650 lm
- Intensity
- 69600 cd
- Throw
- 528 m
- CD/LM factor
- 107.08
Software
The T28 Artemis has mode memory. Mode memory means that the light will remember the mode you were using when the light was last turned off, and when you turn it on again. The ramping mode of the T28 Artemis is intuitive, and lets you seamlessly ramp the output up and down over almost the entire output range.
- Mode memory
- yes
- Ramping mode
- yes
- Strobe
- no
- SOS/Beacon
- no
Features
The battery indicator lets you know when the battery is low, charging, or fully charged. The T28 Artemis cannot charge batteries directly. You may need an external charger to keep your battery going. This flashlight has a built-in low voltage protection (LVP) to prevent damage to the cell from over-discharge, so protected cells are not necessary. The built-in thermal control automatically adjusts brightness output to prevent overheating.
- Battery
- 1 x 21700 Li-Ion battery
- Battery indicator
- yes
- Charger port
- no
- LVP
- yes
- Thermal regulation
- yes
- Protection
- IP66
- AUX LEDs
- no
- Magnetic
- no
- Specials
- green light
red light
white light
zoomable
Accessories
It comes with a battery. The battery must be fully charged before you first use your T28 Artemis. The lanyard prevents accidental loss of the flashlight.
- Package contents
- 21700 battery with USB Type-C
USB Type-C cable
lanyard
remote switch
The performance of the Brinyte T28 Artemis flashlight is measured according to the ANSI / NEMA FL1 Standard 30 seconds after switching the light on. The ANSI/NEMA FL1 2009 Standard is a set of flashlight performance guidelines.
The specifications above are based on the official data published by the manufacturer, but we also take user reviews into consideration. If you found an error or something lacking in the specifications above for the Brinyte T28 Artemis, then don’t hesite and signal the problem to us.
Brinyte T28 Artemis (T28) pictures

If there’s information about the Brinyte T28 Artemis that you would like to see on this site, then write to us.