FlashlightChart.com
FlashlightChart.com / Flashlights / Skilhunt / Skilhunt E2A (2020)
Skilhunt

Skilhunt E2A (2020) review

2020
Luminus SST20 LED
600 lm output
4100 cd intensity
1 x 14500 Li-Ion or 1 x AA NiMH battery

The Skilhunt E2A (E2A) released in 2020. It uses Luminus SST20 LED, TIR reflector and 1 x 14500 Li-Ion or 1 x AA NiMH battery. The powerful emitter in this flashlight provides up to 600 lm output, 4100 cd intensity, and a beam distance of 128 m.

It uses a TIR lens to form the beam pattern. The memory function is a nice feature, the light will remember the last used mode.

Table of contents:

Skilhunt E2A (E2A) specifications

Brand
Skilhunt
Name
E2A
Type
E2A
Rating
Rated 4/5 based on 348 user votes.
Launch
2020
Form
flashlight

Body

The aluminium body of flashlight treated with a Type III hard-anodized, anti-abrasive finish.

Weight
25 g
Length
85 mm
Body diameter
18 mm
Head diameter
19 mm
Material
aluminium alloy with HAIII hard-anodized finish
Colors
black
gun metal gray

System

The emitter of E2A manufactured by Luminus, a US-based LED manufacturer. A TIR lens works on the principle of total internal reflection. The TIR lens collimates the LED light into efficient, well-controlled light beams that maximize the usable lumens in the target area.

Emitter
Luminus SST20 LED
Color temperature
4000 K, 5000 K, 6500 K
Reflector
TIR
Lens
TIR
Switch
twisty

Performance

The throw is the calculated distance in meters at which the flashlight produces a light intensity of 0.25 lux. The candela per lumen (cd/lm) ratio can be used to determine if a flashlight has a spot or flood type beam. Well-focused spot beams can be over 100 cd/lm, tactical flashlights are typically between 20-100 cd/lm, and work lights are less than 10 cd/lm.

Flux
600 lm
Intensity
4100 cd
Throw
128 m
CD/LM factor
6.83

Software

The E2A has mode memory. Mode memory means that the light will remember the mode you were using when the light was last turned off, and when you turn it on again.

Modes
3 mode
Mode memory
yes
Ramping mode
no
Strobe
no
SOS/Beacon
no

Features

The E2A cannot charge batteries directly. You may need an external charger to keep your battery going. A protected battery is recommended as the light itself does not have low voltage protection (LVP). This light does not have temperature control feature.

Battery
1 x 14500 Li-Ion or 1 x AA NiMH battery
Battery indicator
no
Charger port
no
LVP
no
Thermal regulation
no
Protection
IPx8
Impact resistance
1 m
AUX LEDs
no
Magnetic
no

Accessories

It comes with a battery. The battery must be fully charged before you first use your E2A. The clip is useful to keep the light secured in your pocket. The lanyard prevents accidental loss of the flashlight.

Package contents
2 x spare o-rings
AA battery
clip
lanyard

The performance of the Skilhunt E2A flashlight is measured according to the ANSI / NEMA FL1 Standard 30 seconds after switching the light on. The ANSI/NEMA FL1 2009 Standard is a set of flashlight performance guidelines.

The specifications above are based on the official data published by the manufacturer, but we also take user reviews into consideration. If you found an error or something lacking in the specifications above for the Skilhunt E2A, then don’t hesite and signal the problem to us.

Skilhunt E2A (E2A) pictures

Skilhunt E2A / E2A photo Skilhunt E2A / E2A photo Skilhunt E2A / E2A photo Skilhunt E2A / E2A photo
Skilhunt E2A / E2A

If there’s information about the Skilhunt E2A that you would like to see on this site, then write to us.

Back to Top