Olight Warrior 3 (2021) review
The Olight Warrior 3 (WARRIOR3) released in 2021. It uses Luminus SFT70 LED, SMO reflector and 1 x 21700 Li-Ion battery. The powerful emitter in this flashlight provides up to 2300 lm output, 23000 cd intensity, and a beam distance of 303 m.
It uses a TIR lens to form the beam pattern. This light has 5 modes of lighting. The memory function is a nice feature, the light will remember the last used mode. It has a strobe function, which is one of the most effective self defense tools available. The Warrior 3 flashlight is rechargeable easily via USB port.
Table of contents:
Olight Warrior 3 (WARRIOR3) specifications
- Warrior 3
The aluminium body of flashlight treated with a Type III hard-anodized, anti-abrasive ﬁnish.
- 176 g
- 139 mm
- Body diameter
- 26.2 mm
- Head diameter
- 29.5 mm
- aluminium alloy with HAIII hard-anodized finish
The emitter of Warrior 3 manufactured by Luminus, a US-based LED manufacturer. The Warrior 3 has a smooth reflector. The properly focused smooth reflector gives you a more cohesive hotspot and therefore throws better. A TIR lens works on the principle of total internal reflection. The TIR lens collimates the LED light into efficient, well-controlled light beams that maximize the usable lumens in the target area.
- Luminus SFT70 LED
- Color temperature
- 6000 K
- electronic side, electronic rear
The throw is the calculated distance in meters at which the flashlight produces a light intensity of 0.25 lux. The candela per lumen (cd/lm) ratio can be used to determine if a flashlight has a spot or flood type beam. Well-focused spot beams can be over 100 cd/lm, tactical flashlights are typically between 20-100 cd/lm, and work lights are less than 10 cd/lm.
- 2300 lm
- 23000 cd
- 303 m
- CD/LM factor
The Warrior 3 has mode memory. Mode memory means that the light will remember the mode you were using when the light was last turned off, and when you turn it on again. The Warrior 3 is tactical strobe ready. The strobe light is disorienting to the person it is aimed at which makes it difficult for them to concentrate.
- 5 modes
- Mode memory
- Ramping mode
This flashlight can charge the battery with an integrated charger, and it works with any USB power source. This flashlight has a built-in low voltage protection (LVP) to prevent damage to the cell from over-discharge, so protected cells are not necessary. The built-in thermal control automatically adjusts brightness output to prevent overheating.
- 1 x 21700 Li-Ion battery
- Battery indicator
- Charger port
- magnetic USB
- Thermal regulation
- Impact resistance
- 1.5 m
- AUX LEDs
It comes with a battery. The battery must be fully charged before you first use your Warrior 3. The package includes a holster to safely store your flashlight. The clip is useful to keep the light secured in your pocket. The lanyard prevents accidental loss of the flashlight.
- Package contents
- 5000 mAh 21700 battery
MCC3 magnetic USB charger cable
The performance of the Olight Warrior 3 flashlight is measured according to the ANSI / NEMA FL1 Standard 30 seconds after switching the light on. The ANSI/NEMA FL1 2009 Standard is a set of flashlight performance guidelines.
The specifications above are based on the official data published by the manufacturer, but we also take user reviews into consideration. If you found an error or something lacking in the specifications above for the Olight Warrior 3, then don’t hesite and signal the problem to us.
Olight Warrior 3 (WARRIOR3) pictures
If there’s information about the Olight Warrior 3 that you would like to see on this site, then write to us.